PXIe Source Measure Unit
S2014C
12-channel PXIe SMU
The S2014C is a high precision, compact, cost-effective, 12-channel PXIe Source/Measure Unit (SMU) with the capability to source and measure both voltage and current. It has maximum ±10 V, ± 50mA (DC/pulse) sourcing capability. It supports conventional SCPI commands for easy programming. It supports most standard PXIe chassis and multi-card synchronization. The S2014C can be integrated into production test environment to achieve test efficiency improvement and cost reduction.
Features
High range, High-speed Measurement
±10 V, ±50 mA（DC/pulse）
12-channel Testing System
Based on standard PXIe chassis
Adaptive PFC System
Utilizing Adaptive System
Sensing Mode
Supports 2-wire or 4-wire (remote sensing) connectionFunctions and Advantages
5 Functions In One Card
Voltage source
Test Various Devices
Capture More Measurement Data
Rich Scanning Functions
|
Voltage Precision
|
Measuring Range[1] |
Measuring Resolution |
Accuracy (1 year) ± (% reading + bias)[2] |
Typical Noise (RMS) 0.1 Hz-10Hz |
|
±10V |
1 μV |
0.02%+500μV |
100 μV |
|
| ±6V | 1 μV | 0.02%+300μV | 50 μV | |
|
Temperature Coefficient |
±(0.15 × Precision Indicator)/°C (0℃-18℃,28℃-50℃) |
|||
|
Channel[3] |
CH1-CH12 |
|||
|
Overshoot |
<±0.1% (typical,normal, step range is 10% to 90%,full scale point,resistive load test) |
|||
| Noise(10Hz-20MHz) | <3
mVrms，10V voltage source，50 mA resistive load | |||
[1] Please do not connect the Guard terminal to any output, including shorting to chassis ground or output LO, as it may damage the instrument
[2] Example of accuracy calculation: Testing the accuracy of a 1V output in a 10V range, the allowable tolerance is
[3] All channel outputs are electrically isolated from earth, but each channel output shares a common ground (LO)
|
Current Precision
|
Measuring Range |
Measuring Resolution |
Accuracy (1 year) ± (% reading + bias) |
Typical Noise (RMS) 0.1 Hz-10Hz |
|
±50 mA |
10 nA |
0.05%+12μA |
1 μA |
|
| ±10 mA | 10 nA | 0.05%+2 μA | 100 nA | |
|
±1 mA |
1 nA |
0.05%+200nA |
10 nA |
|
|
±100 μA |
100 pA |
0.05%+20nA |
1 nA |
|
|
±10 μA |
10 pA |
0.05%+2nA |
100 pA |
|
| ±1 μA | 1 pA | 0.05%+300pA | 50 pA | |
|
Temperature Coefficient |
±(0.15 × precision indicator)/°C (0℃-18℃,28℃-50℃) |
|||
|
Channel |
CH1-CH12 |
|||
|
Overshoot |
<±0.1% (typical value,normal, step range is 10% to 90%,full scale point,resistive load test) |
|||
|
Configuration Method |
Configuration Range |
|
NPLC |
0.00005PLC ~ 10PLC |
|
Sampling Rate |
5sps ~ 1.0Msps |
Similar recommendation
High speed communication test plays an important role in the rapid development of big data, cloud computing, 5G communication and other markets.
Semight offers various of instruments for optical Transceiver/Component testing, including wide bandwidth sampling oscilloscope, NRZ/PAM4 bit error ratio tester , burst error ratio tester, fast wavelength meter, high precise source measure unit, 400G network analyzer ,optical power meter, optical attenuator, optical switch etc. We provide cost-effective, complete solutions for optical testing.
The high-precision source measure units integrates the functions of voltage source, current source, voltmeter, ampere meter, and electronic load in one, which is widely used in high-precision IV test and measurement for various discrete components, photovoltaic, green energy, battery and other industries. Semight provides high-precision benchtop SMU and plug-in PXIe SMU of standard PXIe chassis, fully meeting the application of various test scenarios.
Details
Burn-in testing of laser is an important method to ensure the reliability of laser. Through the test of CoC or bare die, the early failure of laser caused by the defects in the process of laser production can be screened out in advance. Semight provides a complete solution from bare die to CoC, from high temperature(150℃ or higher) to low temperature (-40℃), with CoC automatic loading and unloading system, forming a complete test solution, Semight's laser chip burn-in/load/unload test system has been widely recognized by the market.
Details
The semiconductor front-end test is mainly used in the wafer processing to check whether the processing parameters of the wafer products meet the design requirements or there are defects affecting the yield after each step of the manufacturing process. The semiconductor back-end test equipment is mainly used after wafer processing to check whether the performance of the chip meets the requirements, which belongs to the electrical performance test. Semight provides solutions such as Wafer Level Burn In system and Known Good Die handler for SiC testing, offering the value to customer in test efficiency improvement and test cost reduction.
DetailsFollow
Name
E-mail verfication code
Phone
Password
Confirm Password
E-mail address
E-mail verification code
New Password
Confirm Password
Ask for demo
