Pulse
S3029H
Precision Pulse SMU
S3029h is a single channel, pulse current source aimed for testing LiDAR. It supports high-precision pulse current output and synchronous measurement of pulse current with DUT voltage drop.
Features
Pulse Width
Minimum 3μs, maximum 500μs
High-speed Measurement
ADC up to 100MSa/s
High Range
Range: ±1.5A, 10V
Stronger Load Adaptability
Test loads with different characteristics to ensure that the waveform does not experience overshoot or other distortions
Closed-loop Current Control
Higher current accuracy
Real Time Reading of DUT Voltage Drop for Pulse Current
No additional equipment required, precise monitoring of current testing conditions, real-time reading back of test resultsFunctions and Advantages
Working conditions
Temperature 23 ℃± 5 ℃
Relative humidity<70%
|
Parameter |
Specifications |
||
|
Current Accuracy |
Range |
Programming Resolution |
Accuracy ±(%RD+mA) |
|
±150mA |
20μA |
0.1%+0.2mA |
|
|
±750mA |
20μA |
0.1%+0.3mA |
|
|
±1.5A |
40μA |
0.1%+0.8mA |
|
|
Current Noise |
Range |
Noise Typical Value (Resistance Load,RMS) 10k-20MHz |
|
|
±150mA |
1mA |
||
|
±750mA |
1mA |
||
|
±1.5A |
1mA |
||
|
Maximum Load Drop Voltage |
10V |
||
|
Pulse Width Resolution |
80ns |
||
|
Maximum Pulse Width Ton-max |
500μs |
||
|
Minimal Pulse Width Ton-min |
3μs |
||
|
Pulse Minimum Turn-off Time Toff-min |
100μs |
||
|
Pulse Width Accuracy |
100ns[1] |
||
|
Pulse Width Jitter |
80ns(typical value) |
||
|
Pulse Period Jitter |
500ns(typical value) |
||
|
Rising Time(10%-90%) |
<400ns[2][3][4] |
||
|
Pulse Overshoot |
<0.5%[2][3][4] |
||
|
Current Regulation Rate |
Linear |
0.05% of Range |
|
|
Load |
±100μA |
||
|
Duty Cycle[5] |
D≤50% when meet: D<3-|Ibias|/[(Vsp-Vload)*(|Iset|-|Ibias|)] |
||
|
Maximum Number of Pulses Per Scan |
64k |
||
[1] Bias current>1mA
[2] Test with short of output line
[3] Total inductance of output line and DUT less than<200nH(100k)
[4] Pulse width measured from 10% of rising edge to 90% of falling edge
[5] Iset:programming current; D: duty cycle;Vsp:source protection voltage; Vload:load voltage
|
Parameter |
Specifications |
||||
|
Pulse Voltage Measure |
Range |
Display Resolution |
Accuracy ±(%RD+mV) |
Sampling Rate [6] |
|
|
6V |
1mV |
0.1%+22mV |
100MSa/s |
||
|
10V |
1.5mV |
0.1%+24mV |
|||
|
Pulse Current Measure |
Range |
Display Resolution |
Accuracy ±(%RD+mA) |
Sampling Rate |
|
|
150mA |
40μA |
0.1%+1mA |
100MSa/s |
||
|
750mA |
100μA |
0.1%+3mA |
|||
|
1.5A |
200μA |
0.1%+7mA |
|||
|
Remote Sense Limit (Voltage Measure) |
Maximum voltage between HI and SENSE HI = ±10V; Maximum voltage between LO and SENSE LO = ±10V; |
||||
[6] Maximal sampling rate for user setting
|
Parameter |
Specifications |
||||
|
Voltage Source(DC) |
Range |
Programming Resolution |
Accuracy ±(%RD+mV) |
Ripple(RMS) 10k-20MHz |
Maximum Output Current |
|
±10V |
1mV |
0.1%+1.5mV |
<5.5mV |
10mA |
|
|
Current Measure(DC) |
Range |
Programming Resolution |
Accuracy ±(%RD+nA) |
Sampling Rate |
NPLC Setting |
|
100μA |
30nA |
0.1%+0.5μA |
100MSa/s |
10 NPLC |
|
|
100nA |
30pA |
0.1%+0.5nA |
|||
|
Voltage Measure(DC) |
Range |
Programming Resolution |
Accuracy ±(%RD+mV) |
Sampling Rate |
|
|
±10V |
1.5mV |
0.1%+15mV |
100MSa/s |
||
|
Remote Sense Limit (DC Voltage Measure) |
Maximum voltage between HI and SENSE HI = ±1V; Maximum voltage between LO and SENSE LO = ±1V; |
||||
|
Parameter |
Specifications |
|||
|
Current Accuracy |
Range |
Maximum Current |
Programming Resolution |
Accuracy |
|
±0.15A |
50mA |
20μA |
0.1%+0.2mA |
|
|
±0.75A |
20μA |
0.1%+0.2mA |
||
|
±1.5A |
40μA |
0.1%+0.2mA |
||
|
Current Noise |
Noise Typical Value(Resistive Load,RMS) 10k-20MHz |
|||
|
<1mA |
||||
Similar recommendation
High speed communication test plays an important role in the rapid development of big data, cloud computing, 5G communication and other markets.
Semight offers various of instruments for optical Transceiver/Component testing, including wide bandwidth sampling oscilloscope, NRZ/PAM4 bit error ratio tester , burst error ratio tester, fast wavelength meter, high precise source measure unit, 400G network analyzer ,optical power meter, optical attenuator, optical switch etc. We provide cost-effective, complete solutions for optical testing.
The high-precision source measure units integrates the functions of voltage source, current source, voltmeter, ampere meter, and electronic load in one, which is widely used in high-precision IV test and measurement for various discrete components, photovoltaic, green energy, battery and other industries. Semight provides high-precision benchtop SMU and plug-in PXIe SMU of standard PXIe chassis, fully meeting the application of various test scenarios.
Details
Burn-in testing of laser is an important method to ensure the reliability of laser. Through the test of CoC or bare die, the early failure of laser caused by the defects in the process of laser production can be screened out in advance. Semight provides a complete solution from bare die to CoC, from high temperature(150℃ or higher) to low temperature (-40℃), with CoC automatic loading and unloading system, forming a complete test solution, Semight's laser chip burn-in/load/unload test system has been widely recognized by the market.
Details
The semiconductor front-end test is mainly used in the wafer processing to check whether the processing parameters of the wafer products meet the design requirements or there are defects affecting the yield after each step of the manufacturing process. The semiconductor back-end test equipment is mainly used after wafer processing to check whether the performance of the chip meets the requirements, which belongs to the electrical performance test. Semight provides solutions such as Wafer Level Burn In system and Known Good Die handler for SiC testing, offering the value to customer in test efficiency improvement and test cost reduction.
DetailsFollow
Name
E-mail verfication code
Phone
Password
Confirm Password
E-mail address
E-mail verification code
New Password
Confirm Password
Ask for demo
